Transcript
Professional Guide For Installing Z wave Door Lock dvslocksmith.com/2022/06/10/professional-guide-for-installing-z-wave-door-lock
The Yale B1L Key Free Keypad Deadbolt, B1L with Z Wave door lock installation technique is covered in this article. This handbook will assist you in the following areas: 1. Existing Door Hardware Must Be Removed 2. Double-check your door dimensions. 3. Install your B1L Keyless Keypad Deadbolt. 4. Free Keypad Deadbolt B1L Programming
Important Measures Before You Begin 1. Remove any existing hardware, such as the lock and strike plate, if one is already present on the door. 2. Please note that removing the existing hardware may necessitate the use of a different screwdriver. 3. Check the door measures twice: Measure your door using the accompanying door checker from the installation envelope to ensure it fits the following requirements: 4. 2 18″ diameter cross boreholes are required. 5. 1″ diameter edge bore holes are required. 6. 2 3/8″ or 2 34″ should be the backset.
Kindly Remember: If the preexisting lock apertures on your door do not meet the required standards, you will need to re-drill them after attempting to remove the lock or consult with an Installations Pro to ensure that they are the correct size. Keep the old lock in place until the placement and testing are finished.
Installation Procedure However, to get the professional help you may contact the lock installation in Elmwood Park.
What You Will Require: The following is a list of everything you’ll need to get started with this lock installation. Check that all of the following components were included in the packaging: 1. A keypad on the Outside 2. Template for a door 3. Batteries: 4 AA 4. The deadbolt on the inside 5. Plate de montage 1/6
6. Cover for the battery 7. Hardware for Mounting 8. Latch 9. Plate of Strike 10. 4 x Machine and Wood Screws 11. 3 x Small Machine Screws, Black 12. Bolts with 2x Long Through Bolts 13. Phillips Head Screwdriver (Standard)
Step 1: Assemble The Strike Plate And Clasp Firstly, you need to use 2″ screws to fasten the strike plate into the doorframe. 2 3/8″ is the latch’s setting. After that, install the latch in the stretched and unlocked position on the door. However, if you need a larger size for installation, adjust the latch to 2 34″. Install the latch with the up arrow facing upwards and fasten it with the two latch screws that come with it. The tailpiece slot is oriented horizontally, while the lock latch is oriented up.
Step 2: Install The Exterior Keypad Secondly, install the keypad lock on the outside of the door so that it is flush with the surface. Make sure the wires are tucked beneath the lock.
Step 3: Put The Mounting Plate In Place From the inside portion of the lock, disconnect the charger cord and the inside mounting plate.
2/6
3/6
Use the below code to embed this infographic Thirdly, pass the wire assembly through the interior mounting plate’s cable hole. Before using the two through bolts, make sure it’s flush with the door and straight. Moreover, choose a through bolt that is adequate for the thickness of your door. With the door checker supplied in the installation guide envelope, double-check that the throughbolt is correct.
Step 4: Put The Cable Assembly Together Connect the cable to the white connector, making sure that the cable’s two white ridges face you. Make sure the cable fits under the hook.
Step 5: Put The Inside Lock In Place Install the lock’s interior piece, making sure the tailpiece fits into the thumb turn shaft assembly. Moreover, you need to insert two mounting screws into the battery housing and one into the bottom of the lock’s interior piece.
Step 6: Check The Lock’s Mechanical Operation Most importantly, turn the inside thumb-turn many times to make sure the lock is working properly. Check the installation processes starting with the latch and strike plate installation if the thumb-turn action fails.
Step 7: Place The Batteries And The Battery Cover In Place Lastly, you need to insert 4 AA batteries. Before adding the batteries, make sure the deadbolt is retracted (unlocked). Replace the battery cover and tighten the screw that holds it in place.
How To Use The Z Wave Door Lock You can also search for a residential locksmith in Chicago, Il. To set up the lock and keypad, follow the procedures below: To alter the lock settings, a master PIN code is necessary. Experts recommend that setting your master PIN code to 6 or more digits is an important security practice. To set the master PIN code, follow these steps: 1. To make a 4- to 8-digit master PIN code, press the gear key first. 2. Then press “1” and the gear key. 3. Then press the shift key to enter your 4- to 8-digit master PIN code.
4/6
The master PIN code for your account has now been created. It’s critical to keep the master PIN code in mind in case you need to reset the lock in the future. Also Read: List of Top Door Chain Lock With Key
Taking Care Of The Lock To finish handing, press any key after entering the Master PIN code. Make your own PIN codes. Before you can create any other PIN codes, you must first create a master PIN code. 1. Firstly, press the gear key to enter your 4- to 8-digit master PIN code. 2. Secondly, press “2,” followed by the gear key. 3. Thirdly, press “1” and the gear key. 4. Lastly, press the gear key to enter a 4-8 digit user PIN code. 5. Now, you have created a PIN code for a user. Enter the master or user PIN code, then check the mark, to unlock the door. Instead of utilizing your master PIN number to unlock your door, we recommend creating a second user PIN code for everyday use.
Installing A New Lock Into A Z Wave Door Lock System For the lock to be enrolled or withdrawn from the network, your network controller must first be in enrollment or exclusion mode. The lock can be enrolled or deleted in the Z-Wave network in two ways: through the keypad using the 7 key (see Programming Through Menu Mode) or by hitting the Z-Wave button after the controller is in enrollment or exclusion mode. To use the Z Wave Door Lock button to enroll a lock, follow these steps: 1. Disconnect the battery cover from the battery. 2. Hold down the Z-Wave button until the unit beeps twice. 3. When you release the button, the network connecting process begins automatically. 4. Remove the battery cover and replace it. 5. To use the Z-Wave button to unlock the door, follow these steps: 6. Remove the battery cover from the battery. 7. Hold down the Z-Wave button until the device beeps five times. 8. When you release the button, the network is automatically removed. 9. Remove the battery cover and replace it.
Conclusion: In conclusion, we can say that installing a Z wave Door lock is an easy process. Moreover, it is more secure and safe.
5/6
Must Read: HOW TO LOCK BIFOLD DOOR LOCK
6/6
