Transcript
Lynx Plus Lynx Plus Lynx Plus Lynx Plus Series Control Series Control Series Control Series Control
Quick Installation Guide
This Quick Installation Guide can help you install the rechargeable Lynx Plus Series Control quickly and easily by providing the basic steps for installation using the built-in defaults and the
Voice Prompt Programming mode. The Voice Prompt Programming mode allows you to quickly program the system by responding to a series of voice prompts.
FOR DOCUMENTATION AND ONLINE SUPPORT: http://www.security.honeywell.com/hsc/resources/MyWebTech (see Lynx Plus Series Installation and Setup Guide P/N 800-
03857V1 or higher.) A copy of the Installation and setup Guide may also be requested from Honeywell.
WARRANTY INFORMATION
For the latest warranty information, please go to:
www.honeywell.com/security/hsc/resources/wa
1. Install the Control
BACK
CASE
1000-300-028-V0
TELEPHONE
CONNECTION
AUDIO CABLE
MOUNTING
HOOKS
7720P
PROGRAM-
MING JACK
TIE-WRAP
POINT
WIRE
ROUTING
TUNNELS
TIE WRAP
FRONT
CASE
ECP/POWER
CABLE
BATTERY
CONNECTIONS
BATTERY
CABLE
TIE WRAP
MOUNT
NOTE
ENSURE ALL WIRING
IS ROUTED THROUGH
WIRE STRAIN RELIEF
CLIP
ROTATE
FRONT
CASE
UPWARD
TO
RELEASE
HOOKS
LOCKING TABS
PLCD
CONNECTOR
GSMVLP COMMUNICATION
PORT
GSMVLP AUDIO
CABLE CONNECTOR
2. Make Wiring Connections
UL NOTE
THE MINIMUMWIRE SIZE USED FORTELEPHONE
INSTALLATIONS MUST BE #26 GAGE
WARNING
TO PREVENT
RISK OF SHOCK,
DISCONNECT
TELEPHONE LINE
AT TELECOM
JACK BEFORE
SERVICING
THIS UNIT
1000-100-004-V0
NOTE
USE ONLY THE
K10145WH/K10145X10
OR K10145CN
TRANSFORMER
PROVIDED
PREMISES
TELEPHONE
INCOMING
TELEPHONE
LINE
6-14VDC
120mA max.
BELL
1 2 3 4 8 6 5 11 7 10
PHONE ZONE SOUNDERS AC
EARTH
GROUND
9
K10145WH/K10145X10
OR K10145CN
PLUG-IN
TRANSFORMER
9VAC, 25VA
RING TIP RING TIP
INCOMING
PHONE
LINE
8
POS
JACK
AC
AC
AC
AC SOUND
OUT HWZ T R T R
ALL OUTPUT CIRCUITS ARE POWER LIMITED.
HARD
WIRED
ZONE
2k
OHMS
EOLR
EARTH
GROUND
Note: For the complete Summary of Connections, refer to the Lynx Plus
Series Installation and Setup Guide P/N 800-03857V1 or higher
3. Make Battery Connections
1000-300-007-V0
BATTERY PACK
NOTE
WALYNXRCHKIT-SHA
BATTERY PACK SHOWN
RETAINER
SCREW
4. Program the Control
Change the Installer Code
The factory default Installer Code for the Lynx Plus Series Control is set
to 4-1-1-2. To change this code, you must enter Expert Programming
mode.
1. After Power-up, enter Installer Code + 8 0 0 or press both the [7]
and [#] simultaneously within 50 seconds after power is applied to
the control. The system will enter the Expert Programming Mode
and “20 INSTALLER CODE” will be displayed.
Note: Upon power-up or after exiting program mode, the system takes up
to a minute to reset. To bypass the reset delay, enter [#]+[0].
2. Enter 720
3. Enter a new four-digit Installer Code.
Program variable data fields
1. If required, enter 724 to program the desired 2-digit RF House ID
for wireless keypads.
2. If required, enter 740 to program a PABX Access Code or to
Disable Call Waiting (LynxSIA Plus only).
3. Enter 794 to program the downloading computer phone number.
4. Press the ESCAPE/ OFF key to enter Voice Prompt Program
mode. The system will announce, “Programming, use arrows to
scroll choices, press select to accept, press escape to quit.” The
system will announce the available options.
1. Separate the front case from the rear case by rotating the front
case and releasing the hooks from the rear case.
2. Feed the wiring through the openings provided in the rear case.
3. Mount the rear case to a sturdy wall and secure with the provided
screws.
3. Reconnect the front case and rear case.
1. Make earth ground connections to terminal 1.
2. Connect the incoming phone line to either the 8-position jack or
terminals 2 (TIP) and 3 (RING).
3. Connect the handset phone lines to terminals 4 (TIP) and 5
(RING).
Note: For full line seize operation, refer to the Lynx Plus Series Installation
and Setup Guide.
4. If used, connect a bell to terminals 8 (-) and 9 (+).
5. Connect the sensors/contacts to the hardwired zone terminals 6
(-) and 7 (+).
6. If used, install the GSMVLP communications device in
accordance with Installation Guide to the GSMVLP
communications port.
7. If used, connect the GSMVLP ECP/Power Cable and the GSMVLP
Communications Cable between the communications device and
the appropriate connectors on the control.
8. Connect wires from the K10145WH/K10145 OR K10145CN
Transformer to terminals 10 and 11.
Note: If using Powerline Carrier Devices refer to the Lynx Plus Series
Installation Guide P/N 800-03857V1 or higher.
1. Remove screw securing the battery retainer.
2. Remove the battery retainer.
3. Insert battery pack into back plate.
4. Install battery retainer.
5. Install screw to secure the battery retainer.
6. Connect battery connector to receptacle on PC board.
7. After all wiring connections have been made, snap the front
assembly to the back plate so it is held by the locking tabs.
8. Plug the transformer into a 24-hour, 110VAC unswitched
outlet.
Note: Rechargeable batteries may take up to 48-hours to fully
charge. “LOW BAT” message should clear within four hours,
or by entering Test Mode.
Battery
Part Number
Battery Standby
Time (Minimum) Low Battery Notification
LYNXRCHKIT-SC 4-hours Approx. 1-hour before battery depletion
LYNXRCHKIT-HC 24-hours At least 1-hour before battery depletion
LYNXRCHKIT-SHA 24-hours At least 1-hour before battery depletion
5. Follow the directions provided by each voice prompt to make your
selections.
The FUNCTION/ # key can be used to repeat a voice prompt,
as required.
6. When you have completed each programming procedure the
system will return to the Main Programming Menu.
Note: If you are installing a GSMVLP in conjunction with the control
refer to the Programming Notes shown below.
Viewing data fields
1. To view data entered in field, press [#] plus the field that you wish
to view (e.g., #21). The system will beep three times and data
programmed for that field will be displayed to the right of the field
number. The system will scroll through the data for longer numbers
and a beep will sound after each number is displayed or three times
after the final digit is displayed.
j§¶¶§¶]§]¶§]¶§
800-03860V2 8/10 Rev. A
Programming Notes
When programming the Control to communicate with a GSMVLP Communications Device, Fields 55, 77 and 91 must be programmed as
follows (refer to the Lynx Plus Series Installation and Setup Guide (P/N 800-03857V1 or higher) or Programming Guide (P/N 800-03859 or
higher):
Radio reporting only: Radio reporting with two-way voice via GSMVP:
Field Selection Field Selection
55 3 55 5
77 1, 2 77 2, 2
91 0 or 2* 91 4 * 2 is default, but remote phone control will not work if GSM reporting only is selected.
Once programming of the module is complete, enter Installer Code + OFF at the control to send the registration for the GSMVLP to AlarmNet.
(Continued on reverse side)
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2010 Honeywell International Inc.
www.honeywell.com/security
Programming Notes
Entering Voice Prompt Programming
Power-up the control and enter the Installer Code + 8 8 8.
When you have completed each programming procedure
the system will return to the Main Programming Menu.
Exiting Voice Prompt Programming
Once you have returned to the Main Programming Menu,
press the ESCAPE/ OFF key.
Entering Central Station Phone Numbers
Enter 0-9, #+11 = 7, #+12 =#, #+13 = a pause of 2
seconds.
Entering Central Station Account Numbers
Enter 0-9, #+11=B, #+12 =C, #+13=D, #+14=E,
#+15=F
Programming Zone Types
The Voice Prompt Programming feature can not be used to
program Zone Types 02, 05, 10, 14, and 24. Programming
these zone types must be done using the Expert
Programming Mode.
5. Voice Prompt Programming
Navigating the Voice Prompt Programming Mode
Scroll through the voice menu and follow the instructions provided to
continue using the Voice Prompt Programming Mode.
The following keys are used to navigate through this feature.
1. ESCAPE/ OFF key: Used at any time to exit the current menu and return
to the previous prompt.
2. ADD/ AWAY key: Used to add sensors or keys or save data when
entering phone or account numbers.
3. DELETE/ STAY key: Used to delete a sensor when in the delete
Sensors Menu.
4. SELECT/ AUX key: Used to confirm a selection.
5. 3 ↑ key: Used to scroll forward through menu choices.
6. 6 ↓ key: Used to scroll backward through menu choices.
7. FUNCTION/ # key: Used to repeat a voice prompt.
(This function cannot be used while entering phone or account numbers.)
1000-300-012-V0
ARMED READY
BYPASS
NO DELAY
RECORD
TEST
FUNCTION STATUS
VOLUME PLAY
CODE
LIGHTS ON
LIGHTS OFF CHIME
ESCAPE
ADD
DELETE
SELECT
1 2
4 5
7 8
0
OFF
AWAY
1
2
STAY
AUX 6
9
3
5
6
7
3
4
6a. Add Sensors
The Lynx Plus Series will enroll a sensor once the transmitter has been activated two times. The system will confirm the enrollment
following each subsequent activation of the same transmitter.
Add a Door Sensor
(1) Delay Door Location
Front Back Side Garage Basement
Sliding Hall Kitchen Patio
Add a Window, Motion Detector, or Fire Detection Sensor
(2) Sensor Type (3) Sensor Location (4) Location Modifiers
Window Living room Kitchen Family Room Attic Upstairs Second Floor
Motion Detector Dining room Hall Guest Room Office Downstairs Front
Fire Detection Bedroom Basement Laundry Room Upstairs First Rear
Bathroom Master Bedroom Utility Room Second Side
Nursery Den Garage Third
6a. Add Sensors (Continued)
Add an Emergency Pendant
(5) Pendant Type
Medical Fire Silent Police Police
Add a Wireless Key
When adding wireless keys, wait 5 seconds between
transmissions.
6b. Delete Sensors
Delete Sensors
7. Add Central Station Accounts
Add First Central Station Phone Number
Add First Central Station Account Number
All four digits of the Central Station Account numbers must be
entered. For ten-digit format, all ten digits must be entered.
Refer to the Lynx Plus Series Installation and Setup Guide for
additional information regarding these programming options.
Add Second Central Station Phone Number
Add Second Central Station Account Number
8. Program Additional Options
Enter Expert Programming Mode
Once you have entered the Expert Programming Mode, the
[ESCAPE] key can be used to return to the Voice Prompt
Programming mode. If you are in any of the Interactive Menu
Modes (756, 780, 781, 783, 784 or 785), you must return to
the main menu in that field before pressing the [ESCAPE] key.
The Lynx Plus Series is configured with Factory Default Settings. You
can revise these settings using the Expert Programming Mode. Refer
to the Installation and Setup Guide to view these defaults and to
continue programming the individual fields using this mode.
Exit Expert Programming Mode
When programming is complete, enter 799.
9. Perform Go/No Go Test
Temporarily mount wireless devices in the preferred mounting
location and perform a Go/No Go test to ensure adequate signal
strength is available.
1. Enter Installer Code + [#] + [8] and run Go/No Go Test.
2. Fault each transmitter to ensure all programmed zones are
received.
3. Mount the transmitter in its permanent location.
10. Program User Functions
Set the Real-Time Clock
1. Enter the Installer Code + FUNCTION/ # + 63
2. Follow the Voice Prompts to program the Clock/Calendar.
Change the Master User Code
1. Enter the Installer Code + CODE/ 8 + 02 + desired 4-digit Master
Code.
Add User Codes
1. By following the procedures in the Lynx Plus Series User Guide,
show the User how to add additional User Codes.
11. Test the system
1. Enter the User Code+ TEST keyThe external sounder will sound
for two seconds and all the LCD segments on the keypad display
light for 3 seconds.
2. Open each protected door and listen for three beeps from the
keypad, followed by the zone’s Voice Descriptor. Identification of
each faulted protection point should appear on the display, and
clear when the door is closed.
3. Walk in front of the motion sensor and listen for three beeps and
the zone’s voice descriptor.
4. When testing is complete, enter: User Code + OFF key.
5. Press each key on the key fob to confirm it performs its assigned
function.
Note: Refer to the Lynx Plus Series User Guide for additional information.
